PDA

View Full Version : New Magnum Powers 95mm TB



David Neibert
11-22-2010, 01:33 PM
Charles Warner has agreed to invest in a new casting to build a batch of 95mm Supercoupe throttle bodies. If we get deposits for at least 20 units by 12-10-10, the price will be $300 each, push shipping.

See this post in the Group Buy forum for more details and a info for how to place a deposit.

http://www.sccoa.com/forums/showthread.php?t=117556

David

rzimmerl
11-22-2010, 02:36 PM
Who is going to pioneer the 4" intake tube to match up to this?

XR7 Dave
11-22-2010, 02:55 PM
This is the coolest group buy we've come across in awhile. :D

rzimmerl
11-22-2010, 03:04 PM
Should be a very cool product when finished as a complete intake package.

fturner
11-22-2010, 05:49 PM
The one thing I did notice, that setup won't fit under a stock hood since my 3.5" is rubbing against the hood now so I'm pooched... I can barely afford the TB let alone a whole hood etc.

Fraser

ricardoa1
11-22-2010, 05:54 PM
I dont bennefit from any of this till I get a big mouth inlet. The tube could be made oval at that point where it hits the hood frame buy I know what you are talking about my 3.5" rubs. But I cheer on those that are making progress. :cool:

David Neibert
11-22-2010, 06:20 PM
I think it will be a lot easier to come up with a larger air inlet tube, than to modify the inlet plenum, linkage and throttle cables to accept an oval throttle body. Even if you have an oval throttle body, you are still going to need to fabricate a new air intake tube that transitions from a round MAF to an oval TB. You will also need a differnt throttle position sensor and IAC valve.

This new 95mm TB is really going to make reducing blower inlet restrictions a whole lot easier than the present alternatives. The cost is also very reasonable as compared to a similar sized oval throttle body.

David

ricardoa1
11-22-2010, 06:35 PM
I was not suggesting an oval TB, I was saying that I dont bennefit from a larger then 85MM unless my inlet, I was merely suggesting pinching a 4" tube,making it oval at the point where the shocktower and hood is the problem not sure what that will do to flow.....

rzimmerl
11-22-2010, 06:41 PM
I think a 4" inlet tube is going to require a few horsepower dents, and removing a small chunk of the under hood support to make it fit. I got a hammer and whizzer wheel...;)

David Neibert
11-22-2010, 06:44 PM
I was not suggesting an oval TB, I was saying that I dont bennefit from a larger then 85MM unless my inlet, I was merely suggesting pinching a 4" tube,making it oval at the point where the shocktower and hood is the problem not sure what that will do to flow.....

Sorry Ricardo, I missunderstood you.

David

nickleman60
11-22-2010, 06:59 PM
My deposit's in for the 95mm TB.

XR7 Dave
11-22-2010, 07:51 PM
My deposit for 3 isn't in yet, gotta scrounge up the cash. :eek: I'm all in on this one and I don't care if it presents a couple minor challenges to fit.

Ya Hoo! :D

fturner
11-22-2010, 08:17 PM
I'm going to wait until I can get a larger inlet plenum to the blower someday... no point in going bigger in an area that isn't the flow issue until the actual restriction has been taken care of.

Good luck guys, hope it works out for you :).

Fraser

BLOWN38
11-22-2010, 08:24 PM
Is the bolt pattern gonna match the stock inlet pattern, or we gonna have to drill and tap that? Along with hogging out the inlet bore.

rzimmerl
11-22-2010, 08:26 PM
Is the bolt pattern gonna match the stock inlet pattern, or we gonna have to drill and tap that? Along with hogging out the inlet bore.

Its gonna match, see post #88 in the link David posted.

Roadhawg
11-22-2010, 08:37 PM
Is the bolt pattern gonna match the stock inlet pattern, or we gonna have to drill and tap that? Along with hogging out the inlet bore.


From what Charles said the bolt pattern will match, but I foresee using Allen Cap screws.

BLOWN38
11-22-2010, 08:39 PM
Yeah thanks guys, I saw it in the other thread. Read this one first.:o

David Neibert
11-22-2010, 08:48 PM
From what Charles said the bolt pattern will match, but I foresee using Allen Cap screws.

Absolutely...same as most are already using on their 85mm TB.

David

XxSlowpokexX
11-22-2010, 09:15 PM
I paid for mine....But now to actually get the inlet to flow enough to need it...Oh JOY!

Mike8675309
11-22-2010, 09:40 PM
I paid for mine....But now to actually get the inlet to flow enough to need it...Oh JOY!

i'd get in touch with XR7 Dave to see if he has some ideas for you. my bet is he will.

nmcbchief
11-22-2010, 10:40 PM
My deposit is in!

ricardoa1
11-23-2010, 12:04 PM
I paid for mine....But now to actually get the inlet to flow enough to need it...Oh JOY!

Let me know what you make out.

David Neibert
12-07-2010, 01:23 PM
Just need to get one more order to reach to 20 pc minimum.

David

mellbutler
12-07-2010, 03:35 PM
never mind...delete thought it was 85mm woops

David Neibert
12-07-2010, 03:44 PM
In case anyone else needs the link to where you make the deposit for the new MP 95mm TB. Go here and scroll down the page to the Group Purchase 95mm TB $200 deposit tab.

http://www.magnumpowers.com/thunder_pro_pri.php

David

ricardoa1
12-07-2010, 03:56 PM
never mind...delete thought it was 85mm woops

If you buy my 85MM I can help out on the GB.

mellbutler
12-07-2010, 03:59 PM
pm me how much

ricardoa1
12-07-2010, 04:17 PM
PM sent................................

David Neibert
12-10-2010, 01:14 PM
Group purchase for the 95mm TB ends today.

We have already reached the minimum quanity, so if you want to get this TB at the group buy price, you need to place the order/deposit today.

David

ScrapSC
12-11-2010, 07:56 PM
Called Charles up and paid for mine today. :)