PDA

View Full Version : preping time



forcedbird94
03-06-2011, 03:28 PM
time to build

Nettlesd
03-06-2011, 04:11 PM
Very Nice.

forcedbird94
03-06-2011, 06:08 PM
yeah cant wait till i see it together

forcedbird94
03-07-2011, 05:00 PM
more picks im getting excited been a long time since i drove my car

??you thing i can go to junk yard and grab a set of down pipes off a v6 stang which i got the manifolds from and put them on my bird till i get more money for exuast????

sinhumane
03-07-2011, 08:46 PM
i see you havent modified the drivers side manifold for clearance, have you modified your steering shaft? otherwise, you'll be getting some interference. :)

forcedbird94
03-08-2011, 08:23 AM
i see you havent modified the drivers side manifold for clearance, have you modified your steering shaft? otherwise, you'll be getting some interference. :)

i c how do i do this

Regul8r
03-08-2011, 08:12 PM
i c how do i do this

Not sure what needs to be done.
I have a couple sets of manifolds if you need them.

Silenced
03-09-2011, 10:35 AM
.... That looks .... Sturdy .... I hope you're fastening the motor togeather better than it's fastened to the engine stand.

neverfastenough
03-09-2011, 11:17 AM
+1 get that thing on there correctly.

forcedbird94
03-09-2011, 12:10 PM
.... That looks .... Sturdy .... I hope you're fastening the motor togeather better than it's fastened to the engine stand.

my 429 boss broke my stand i ordered a new one just havent recevied it

TSC89
03-09-2011, 12:30 PM
i c how do i do this

Checkout this website. It has the info you need to modify the Mustang headers.

http://www.supercatxr7.freewebspace.com/photo2.html

forcedbird94
03-09-2011, 01:15 PM
thanks jim ots not as hard as i thought it would be.
can i use mustang down pipes or get some made ether way gonna cost me money but my uncle owns a pipe binder in his auto shop my dad sold him so i might just make extra if thats my rought

eli66048
03-10-2011, 04:08 AM
When I used it on my silver car I cut the driver's side and rotated it to clear the steering then had it rewelded. The passenger side I had the muffler shop redo the connector pipe to it. I was just looking at my son's 96 LX and it has a set on it that may clear with no mods. Maybe just open the end up a little to a larger circumference?

forcedbird94
03-10-2011, 01:35 PM
When I used it on my silver car I cut the driver's side and rotated it to clear the steering then had it rewelded. The passenger side I had the muffler shop redo the connector pipe to it. I was just looking at my son's 96 LX and it has a set on it that may clear with no mods. Maybe just open the end up a little to a larger circumference?

Did you have rocky do it

forcedbird94
03-30-2011, 11:24 AM
Q? i pulled out my 94 trans the fly wheel says aod and the new one says 4r70w will my ecu run this trans i put all electrical:confused: from old to the new here is some pics

Silenced
03-30-2011, 11:48 AM
Um... What year is the car, and what year is the transmission?

forcedbird94
03-30-2011, 12:07 PM
Um... What year is the car, and what year is the transmission?

car is 94 new trans is 96

forcedbird94
03-30-2011, 01:50 PM
bump.................

Silenced
03-30-2011, 02:22 PM
Uhh yeah... I'd make sure the bellhousing is right... I'd bet it's a different bolt circle...

When you say you swapped electronics... What did you mean by that? The 94/95 transmissions have an On/Off style torque converter driver, and the newer ones have a pulse width modulated version that varies pressure

forcedbird94
03-30-2011, 02:30 PM
Uhh yeah... I'd make sure the bellhousing is right... I'd bet it's a different bolt circle...

When you say you swapped electronics... What did you mean by that? The 94/95 transmissions have an On/Off style torque converter driver, and the newer ones have a pulse width modulated version that varies pressure

the only thing i put on the new trans is where the shifter bolts up there is a module not sure what it is

bolt patern and both aod and 4r70w flex plate line up

Silenced
03-30-2011, 02:34 PM
the only thing i put on the new trans is where the shifter bolts up there is a module not sure what it is

bolt patern and both aod and 4r70w flex plate line up

The MLPS... That's only part of it. There is a driver inside the VB... I think the pinout might be different to. This is not a direct swap.

And the bolt pattern I meant was Trans--> Motor

forcedbird94
03-30-2011, 02:38 PM
The MLPS... That's only part of it. There is a driver inside the VB... I think the pinout might be different to. This is not a direct swap.

And the bolt pattern I meant was Trans--> Motor

bolt patern is same made sure when both where out
is the pin out reachable thru the pan
if so what dose it look like and how hard

Silenced
03-30-2011, 02:43 PM
bolt patern is same made sure when both where out
is the pin out reachable thru the pan
if so what dose it look like and how hard

Never done it. You're going to have to search on TCCoA

forcedbird94
04-09-2011, 07:57 AM
yeah baby.........................

forcedbird94
05-06-2011, 07:33 AM
it starts time to take it to muff shop lol thinking of dumping them for sc sound and might go with the flows anyone got sugestions

forcedbird94
05-06-2011, 08:08 PM
bump ............

forcedbird94
05-20-2011, 03:42 PM
new vid on facebook

http://www.facebook.com/video/video.php?v=10150198972963794&saved#!/video/video.php?v=10150198972963794&comments

slowpoke
05-22-2011, 03:38 AM
Checkout this website. It has the info you need to modify the Mustang headers.

http://www.supercatxr7.freewebspace.com/photo2.html

those almost look like mine. mine dont have the off tubes and has been nicely modified around the steering arm. was walking in speedway and an old n/a 3.8 had them hanging. pretty new i assume since it was exposed the the elements and the headers had nearly no rust. the guy at the counter charged me a heavy price for those. i think it was around $10 or so. i didnt see any pics of the headers on file so ill take some in the next few days and post them.