Tab Content
KMT's Activity
About Me
My Vehicles
Post Areas
Tab Content
  • KMT's Avatar
    03-21-2017, 10:46 AM
    I've pulled from Jags, but yes, see the list Sam provided - I went thru 2 or 3 used ones while waiting to get a new one. I'd get the last bit of...
    10 replies | 192 view(s)
  • KMT's Avatar
    03-21-2017, 01:08 AM
    If I remember correctly - pump might run 40 ~ 50 seconds on start up after overnite. Pedal pumps should be more than 6 before the pump is triggered.
    10 replies | 192 view(s)
  • KMT's Avatar
    03-20-2017, 11:29 PM
    They get old....and then act out pretty much as you describe, but how long does it take for the light to go out when you start the car after sitting...
    10 replies | 192 view(s)
  • KMT's Avatar
    03-20-2017, 03:30 PM
    KMT replied to a thread ABS Pump Motor Relay in Technical Forum
    If this was the original relay, contacts in those examples are typically happy to burn without outside influence from a connector, so it may have...
    3 replies | 83 view(s)
  • KMT's Avatar
    03-20-2017, 02:18 PM
    KMT replied to a thread ABS Pump Motor Relay in Technical Forum
    I bought an RY223 6 months back that was correct for that application, at least on my '90 Anny. What process did you use that led you to replace...
    3 replies | 83 view(s)
  • KMT's Avatar
    03-17-2017, 08:03 PM
    ;) Cheaper to keep 'er Last car I modded for resale was a '49 Ford...went from a 6 cyl. flathead to an 8. Turned a sweet $50 profit on that one...
    17 replies | 400 view(s)
  • KMT's Avatar
    03-15-2017, 07:47 PM
    That was at least 3 yrs. ago - try 'Auto Upholstery & Convertible Tops' (Richard?) 3530B SW Multnomah Blvd. in SW Portland/Multnomah Village - I'm...
    17 replies | 400 view(s)
  • KMT's Avatar
    03-15-2017, 02:26 PM
    You might be able to re-stitch the one side that's only just pulled w/o taking it apart, but the side that's blown out would need to be taken apart...
    17 replies | 400 view(s)
  • KMT's Avatar
    03-15-2017, 01:07 PM
    KMT replied to a thread 89 octane or 93 in Technical Forum
    As already noted, you can't remove the worry - once detonation is detected, it's already happened and you're in the danger zone. Trying to save a few...
    12 replies | 310 view(s)
  • KMT's Avatar
    03-15-2017, 12:53 PM
    Right (except on the Anny where the seat middles are pig suede), and much of the bolster, of course, as well as the front seat side bolsters &...
    17 replies | 400 view(s)
  • KMT's Avatar
    03-14-2017, 02:40 PM
    Wonder which brings more $ on resale... My Anny lets me sit on pig skin and isn't my DD now, which falls to my 2002 Windstar w/cloth - I don't...
    17 replies | 400 view(s)
  • KMT's Avatar
    03-14-2017, 12:02 PM
    Didn't Duffy used to tell us that some of the leather was vinyl 'coated' and that's why saddle soap was a waste of time?
    17 replies | 400 view(s)
  • KMT's Avatar
    03-13-2017, 12:07 PM
    Agreed, not worth the trouble, especially if you don't already have the tools to install a press-in joint without damaging it, and as noted, it still...
    2 replies | 147 view(s)
  • KMT's Avatar
    03-11-2017, 05:33 PM
    I posted in your other same thread. Ken
    2 replies | 133 view(s)
  • KMT's Avatar
    03-11-2017, 05:28 PM
    Mine was failing, but not as bad as yours. I had a local upholstery shop give me an estimate, which wasn't too bad, but before I got around to...
    17 replies | 400 view(s)
  • KMT's Avatar
    03-08-2017, 09:25 PM
    Pull each wheel and spin the hub/rotor - if the issue is brake related, it should show up then. If not, look for a loose lug nuts, or a cracked...
    11 replies | 334 view(s)
  • KMT's Avatar
    03-08-2017, 01:26 AM
    Autozone, as an example, loans a cooling system pressure tester (also cap tester). Just install the adapter instead of the cap, then pump it up no...
    20 replies | 746 view(s)
  • KMT's Avatar
    03-08-2017, 12:24 AM
    I've seen examples where the heads and block being milled pushed the intake manifold mating surfaces out of spec, resulting in mismatch that leads to...
    20 replies | 746 view(s)
  • KMT's Avatar
    03-07-2017, 11:47 PM
    Same piston? Just the one? How long does it take for the leak to turn up? Before or after the engine gets to temp? Did you pressure test it after...
    20 replies | 746 view(s)
  • KMT's Avatar
    03-07-2017, 08:09 PM
    KMT replied to a thread Privacy in Non Technical Forum
    Try asking http://www.sccoa.com/forums/member.php?256-David-Neibert, one of the principals.
    3 replies | 271 view(s)
  • KMT's Avatar
    03-07-2017, 11:57 AM
    The OP needs three more posts, first ;) Raining down there? ...joke... Ken
    7 replies | 182 view(s)
  • KMT's Avatar
    03-07-2017, 11:54 AM
    The aftermarket manuals are a bit too casual, often overlooking the SC's particulars. I wouldn't bother with them. Best to buy a factory manual...
    7 replies | 182 view(s)
  • KMT's Avatar
    03-07-2017, 10:47 AM
    Those are large sealed bearings - not designed to be 'repacked'. If they need service, they should be replaced. The nut holds the hub bearing hard...
    2 replies | 129 view(s)
  • KMT's Avatar
    03-06-2017, 01:03 PM
    KMT replied to a thread Knock sensor? in Technical Forum
    Ford seems stingy when it comes to throwing a CEL in some cases, I think...takes a long, hard, consistent fault, I guess. Did you try running a...
    4 replies | 198 view(s)
  • KMT's Avatar
    03-05-2017, 08:33 PM
    KMT replied to a thread A weird issue in Technical Forum
    When you shut off the engine, and let it sit for about 15 minutes, and press the Schrader valve on the fuel rail, is there still fuel pressure there?
    51 replies | 1464 view(s)
  • KMT's Avatar
    03-04-2017, 11:07 PM
    KMT replied to a thread Looking for Working ICRM in Want to Buy
    I see. Might as well try parts then - hopefully someone can help out. Good luck. Ken
    8 replies | 238 view(s)
  • KMT's Avatar
    03-04-2017, 10:17 PM
    KMT replied to a thread Looking for Working ICRM in Want to Buy
    Do you have a way to pull codes and force a self-test of the fan's two speeds?
    8 replies | 238 view(s)
  • KMT's Avatar
    03-04-2017, 08:59 PM
    KMT replied to a thread Looking for Working ICRM in Want to Buy
    Actually, it does - no spares w/that # here I can let go at this time, tho, sorry. What issue are you trying to solve? Are you sure you need a...
    8 replies | 238 view(s)
  • KMT's Avatar
    03-04-2017, 07:47 PM
    KMT replied to a thread Looking for Working ICRM in Want to Buy
    What P/N ~ code?
    8 replies | 238 view(s)
  • KMT's Avatar
    03-03-2017, 11:21 AM
    In my experience, those tracks need some sort of lube. I use spray silicone, usually twice a year down here. Just on the section from the shoulder...
    3 replies | 207 view(s)
More Activity
About KMT

Basic Information

About KMT
Location:
Salem, OR

Statistics


Total Posts
Total Posts
5,957
Posts Per Day
1.76
General Information
Join Date
12-25-2007
  • No Listings in the database at this time.
Post Areas

Top Areas Of Posting