Tab Content
Legion's Activity
About Me
My Vehicles
Post Areas
Tab Content
  • Legion's Avatar
    09-21-2018, 01:26 AM
    Well this got all ~~~~ity ....1/2/3 mains all gave me a little over the 15 thousands of an inch on the plastigauge strip. Then the last one 4 gave me...
    8 replies | 247 view(s)
  • Legion's Avatar
    09-19-2018, 08:51 PM
    Legion replied to a thread Ported gains ? in Technical Forum
    Thanks for the replies!. Yeah I guess I'm just going to send it.i wonder what gains is to be had by converting to split port?. I'm pretty good at...
    6 replies | 304 view(s)
  • Legion's Avatar
    09-19-2018, 08:46 PM
    Yeah that's why I'm wondering? I also figured out that the 96+ blocks from N/A 3.8s aren't the same as SC blocks. They use smaller main caps and...
    8 replies | 247 view(s)
  • Legion's Avatar
    09-18-2018, 08:44 PM
    Got a question. What's the specs for bearing clearances.and what's the deal with plastigauge and these engines? Used it before but some say the last...
    8 replies | 247 view(s)
  • Legion's Avatar
    09-18-2018, 08:40 PM
    Legion replied to a thread Ring end gap in Technical Forum
    Yup sure as ~~~~ it's on point.ring end gap Calculator gave me with a bore of 3.811 and my biggest 3.8125 was .23 and .24 thousands....sounds...
    8 replies | 197 view(s)
  • Legion's Avatar
    09-18-2018, 02:04 PM
    Legion replied to a thread Ring end gap in Technical Forum
    Is that normal to see ? 24 to 25 thousands ? I thought the gap was 10. 12 thousands. Honestly that seems small and dangerous to me unless I'm not...
    8 replies | 197 view(s)
  • Legion's Avatar
    09-18-2018, 02:21 AM
    Legion replied to a thread Ring end gap in Technical Forum
    It's a direct replacement ring kit. Non file fit so I'm guessing this is how it's supposed to be? My last rings in the engine all measured about the...
    8 replies | 197 view(s)
  • Legion's Avatar
    09-18-2018, 02:18 AM
    Legion replied to a thread Ring end gap in Technical Forum
    Yeah they're stock pistons 3.811 bore . All stock stuff.
    8 replies | 197 view(s)
  • Legion's Avatar
    09-17-2018, 10:00 PM
    Legion replied to a thread Ring end gap in Technical Forum
    Never mind lol. They sent me non file fit.....I asked for file fit...this makes sense now...I feel stupid. Anyways my top rings are 25 thousands and...
    8 replies | 197 view(s)
  • Legion's Avatar
    09-17-2018, 09:09 PM
    Legion started a thread Ring end gap in Technical Forum
    Got a new set of rings...sealed power trash. They don't have any specs online and didn't send a sheet with the junk either. I know most ring gaps are...
    8 replies | 197 view(s)
  • Legion's Avatar
    09-16-2018, 11:52 PM
    Legion replied to a thread Ported gains ? in Technical Forum
    I've ported lots of heads before never had issues. Does anyone have any experience with ported stuff??
    6 replies | 304 view(s)
No More Results
About Legion

Basic Information

Statistics


Total Posts
Total Posts
33
Posts Per Day
0.08
General Information
Last Activity
09-24-2018 06:28 PM
Join Date
08-31-2017
  • No Listings in the database at this time.
Post Areas

Top Areas Of Posting