Search:

Type: Posts; User: KMT

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. I think according to the image marked up in red,...

    I think according to the image marked up in red, they are correct.



    I think you are ok, again, according to that image.

    Getting back to the tensioners, did you confirm they all still have...
  2. Replies
    3
    Views
    71

    It's just a press fit into the block - slight...

    It's just a press fit into the block - slight twist and pull. Never had to fight one coming out, but I can imagine it being tight.

    Depending on access where the tube meets the block, you could...
  3. Replies
    3
    Views
    71

    There should be a tab welded to the tube, a few...

    There should be a tab welded to the tube, a few inches from the top, that is bolted to the rear-most stud on the front cylinder exhaust manifold. Once the tab is free, there is about an inch of tube...
  4. Replies
    6
    Views
    81

    I have no idea why Ford decided to make (at...

    I have no idea why Ford decided to make (at least) two different depth bezels (not sure it has to do with the bumper cover thickness), but I seem to recall the difference is early is narrow, meaning...
  5. Replies
    6
    Views
    81

    Just a heads up - when sourcing the cornering...

    Just a heads up - when sourcing the cornering light assemblies, keep in mind there are at least two variations. They may look the same, but the depth of the outer bezel will vary. If you know what...
  6. Part numbers should also reference length, which...

    Part numbers should also reference length, which is what you really want to know:

    Stock belt lengths - examples only, actual length may vary slightly by manuf.:

    Supercharger - 39.17"
    ...
  7. Might want to check the part numbers to confirm...

    Might want to check the part numbers to confirm they're the right belts.
  8. I searched here & the factory manual, and after...

    I searched here & the factory manual, and after going thru several threads and studying photos of engines, I learned they apparently differ by location and tension & came up with the following info:...
  9. Replies
    19
    Views
    363

    If you run a 180 stat, you should also use a...

    If you run a 180 stat, you should also use a chip that allows modified fan turn-on temp etc. Feel free to search for those threads.

    Ken
  10. Replies
    19
    Views
    363

    Got it, thanks. My opinion is yes, in that...

    Got it, thanks.

    My opinion is yes, in that example, with a properly maintained car, it can handle it.

    If a car boils out in that example, something basic needed fixing before you went out.
    ...
  11. Replies
    19
    Views
    363

    What's the question? Street driving as your...

    What's the question? Street driving as your original question seemed to indicate, or track runs, which it seems you're on to now...? Sorry if I didn't take the original hint ;)



    A mod'd car...
  12. Replies
    19
    Views
    363

    According to my data using my '90 Anny with...

    According to my data using my '90 Anny with everything cooling system replaced except for the heater core and an aluminum radiator, I think your numbers are dead on normal.

    As long as your system...
  13. Thread: Cruise Control

    by KMT
    Replies
    6
    Views
    145

    I don't think I see the ignition switch in your...

    I don't think I see the ignition switch in your images.


    Looks like this:
    https://m.media-amazon.com/images/I/814QAR+bH9L._AC_UY218_.jpg

    Bolted to the side of the steering column with...
  14. Thread: Cruise Control

    by KMT
    Replies
    6
    Views
    145

    Have you removed the horn pad on the steering...

    Have you removed the horn pad on the steering wheel and verified those connections are healthy? Horn works ok?

    Going back to your A/C, you found a loose connector, as I recall - has the dash been...
  15. Thread: 1990 Cougar XR7

    by KMT
    Replies
    1
    Views
    75

    5 mm for the bolts holding the crank sensor to...

    5 mm for the bolts holding the crank sensor to the bracket.
  16. Replies
    13
    Views
    292

    Ouch - glad you found it before it went south.

    Ouch - glad you found it before it went south.
  17. Replies
    13
    Views
    292

    Got it, thanks. I'd do low hanging...

    Got it, thanks.

    I'd do low hanging fruit...wheel balance - might mention you're chasing a vibration and ask them to look close.

    You could get the rear off the floor, with the wheels at same...
  18. Replies
    13
    Views
    292

    You started out chasing a vibration at that...

    You started out chasing a vibration at that corner of the car, as I understand it.

    You decided is wasn't the wheel bearing, then went after the upper bushing, now it's worse - does that sum it up?...
  19. Could be a number of things, from worn plugs, to...

    Could be a number of things, from worn plugs, to vacuum leaks, to failing IAC, etc.

    Something you can try that won't cost more than a can of spray carb cleaner, is to remove the black rubber air...
  20. Replies
    13
    Views
    306

    Step-by-step... When I did my headgaskets in...

    Step-by-step...

    When I did my headgaskets in 2018, I had over 2 dozen other things I wanted to deal with that I kept putting off until I was in that far. Added to the repair costs a tad, but I...
  21. Replies
    13
    Views
    306

    I want to say I used a deep 13mm on the stud. ...

    I want to say I used a deep 13mm on the stud.

    Suggest you remove the wiper motor assembly to help overall access.

    Is that the EGR tube in the red square?

    P I T A, yes. Right up there with...
  22. Replies
    13
    Views
    306

    When I said the regulator should come away easy,...

    When I said the regulator should come away easy, I meant as part of the fuel rail, once the stud is removed. And just to stay on the same page, red in your drawing is heater hose/coolant. Blue is...
  23. Replies
    13
    Views
    306

    There is just one vacuum line leading to the...

    There is just one vacuum line leading to the regulator, should be easy to reach and not an impediment to removing the regulator - flexible, sure, durable, usually. Just don't go crayCray yanking on...
  24. Replies
    0
    Views
    78

    Heated Seats ~ Anny

    Decided to skin the driver's seat for worn bolster repair*, and occupancy sensor install, and thought it would be a good time to add a seat heater kit. Might do a write-up later, but for...
  25. Replies
    2
    Views
    86

    What gap? Is there an issue, or are you just...

    What gap?

    Is there an issue, or are you just curious...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4