Search:

Type: Posts; User: TbirdSCFan

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    22
    Views
    612

    Running a can of additive which will clean up the...

    Running a can of additive which will clean up the valve body, at this point, is a good idea. Certainly can't hurt. But do it before you change the fluid and filter.

    The issue with the disconnected...
  2. Replies
    22
    Views
    612

    Its not the bushing. The setting for the AOD TV...

    Its not the bushing. The setting for the AOD TV cable is not that sensitive. I drove for 10 years with one attached with a twist-tie. :eek: and it worked perfectly fine. If its driveable, just drive...
  3. Replies
    2
    Views
    149

    I'll go with that pretty much in that order. ...

    I'll go with that pretty much in that order.

    One thing you can do to verify if its ignition switch, is to rock it fore/aft slightly when the dash lights come on. If the pump motor engages again...
  4. Replies
    19
    Views
    1,370

    Absolutely. Most of the problems with Teves II...

    Absolutely. Most of the problems with Teves II have to do with wear and those tend not to set any codes. Failures tend to be, in order of most common: 1. Accumulator wear, 2. Pump motor relay, 3. ABS...
  5. Check your rear upper control arm frame...

    Check your rear upper control arm frame bushings.. raise the wheel, grab at 12&6 and push/pull. Should be no movement.



    Probably dripping out from the ARC pressure sensor. The one mounted on...
  6. Thread: Plasti Dip

    by TbirdSCFan
    Replies
    8
    Views
    1,538

    I used it for my B pillar and exterior trim...

    I used it for my B pillar and exterior trim paint. I never really could get it thich enough and I'm not impressed with durabaility.
    It hasn't stood up very well to summer heat. In other words.. it...
  7. Replies
    19
    Views
    780

    The side bolsters were not recovered separately...

    The side bolsters were not recovered separately for some reason. The air pump controls for the side bolsters are still there. Im going to guess its not hooked up either.
  8. Replies
    10
    Views
    522

    If the last thing you did was to splice into the...

    If the last thing you did was to splice into the power steering lines, I'd look around there. Something you can do to narrow the search is take off the serp belts and start it up for a minute. That...
  9. Replies
    1
    Views
    190

    If you ask about a supercoupe, we can probably...

    If you ask about a supercoupe, we can probably help you out. Not so much with a neon. :rolleyes:
  10. Where's that laughing "like" button?

    Where's that laughing "like" button?
  11. Replies
    5
    Views
    312

    90% of all SC engine running vacuum related...

    90% of all SC engine running vacuum related problems are due to improperly sealed IC tubes and related plumbing. Your situation sounds just like it. Your idle is too fast for an auto, and the...
  12. Replies
    13
    Views
    778

    Thats the jumper wire I was referring to. I did...

    Thats the jumper wire I was referring to. I did this years ago to bypass the alarm. It was so long back that I have little recall as to the details.
  13. Replies
    1
    Views
    269

    Does it shift ok sitting still? That is with the...

    Does it shift ok sitting still? That is with the engine off, can you work through the gears without a lot of effort? Then what happens when you start the car and go through the gears at idle? I have...
  14. Replies
    13
    Views
    778

    The module in the trunk.. unplug it. :D ...

    The module in the trunk.. unplug it. :D

    However, there is 1 conection that has to be jumpered.. 1 wire.. I'll see if I can locate it later.
  15. Replies
    8
    Views
    509

    If the IAC is good, then when you unplug it, the...

    If the IAC is good, then when you unplug it, the car will struggle to idle.. If it is bad, then unplugging it would result in no difference.

    Remove it.. look inside.. I'd be certain that the...
  16. Replies
    3
    Views
    311

    Thats correct. If you simply unplug it, a lot of...

    Thats correct. If you simply unplug it, a lot of annoying sounds will cease. However, if you don't have the auto headlight module, you may end up regretting that decision some day. ;)
  17. Replies
    19
    Views
    1,370

    Great. Yeah, those are the tips I've worked out...

    Great. Yeah, those are the tips I've worked out over the years. Glad to hear you got it working. :)
  18. Replies
    19
    Views
    1,370

    This is one of the frustrating parts of the...

    This is one of the frustrating parts of the process. What I do now is prime the pump by running the motor/pump from a 12volt power supply, directly to the motor connector, with the accumulator...
  19. Thread: car is dead

    by TbirdSCFan
    Replies
    7
    Views
    551

    If the uparrow stays lit while cranking, then yes...

    If the uparrow stays lit while cranking, then yes the crank sensor signal is lost. The cause of that could be wiring or a bad sensor, or even a balancer issue.
  20. Replies
    19
    Views
    1,370

    Here's a link to the thread ...

    Here's a link to the thread with a part number for a compatible shaft seal. Its not EDPM material, but its cheap.
  21. Replies
    19
    Views
    1,370

    If you have the gumption, look up a compatible...

    If you have the gumption, look up a compatible seal part number and rebuild yourself. The available seal isn't necessarily the preferred material, but its better than an old leaky, and according to...
  22. Replies
    5
    Views
    353

    Aye! Go with the highest grade you can get and...

    Aye! Go with the highest grade you can get and never "service grade" or "economy". And nothing off eBay. If its cheap its because its crap.
  23. I REALLY don't like non store suppliers for these...

    I REALLY don't like non store suppliers for these units. The reason being since their likelihood of failure is so high, and since they are so difficult to verify that they have failed, you can't...
  24. Replies
    23
    Views
    3,214

    OK. As far as that goes. When it is seated, the...

    OK. As far as that goes. When it is seated, the TC studs will not be visible from the side. That is to say if you could line up on side of the trans with other, you wouldn't be able to see ANY part...
  25. Replies
    5
    Views
    500

    How about a blend door problem due to a faulty...

    How about a blend door problem due to a faulty vacuum line or ruputured diaphragm. Or a malfunctioning climate control.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4