Search:

Type: Posts; User: 90coug

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Replies
    1
    Views
    661

    New Engine for the SC

    Was thinking about having Steve build one of these for my SC. :rolleyes:
    ...
  2. Replies
    152
    Views
    20,877

    Possibly, what year did you need it for?

    Possibly, what year did you need it for?
  3. Replies
    152
    Views
    20,877

    Intake Manfifold sold

    Intake Manifold has been sold, thanks Mike C.

    Bump TTT

    :)
  4. Replies
    13
    Views
    1,112

    Right, thanks for the clarification. So, I didn't...

    Right, thanks for the clarification. So, I didn't find any issues with the wiring for the O2's. I then went back to the logs. There are times where bank #1 is adding fuel and bank #2 is removing fuel...
  5. Replies
    13
    Views
    1,112

    Thanks, Matt. I think you might be on to...

    Thanks, Matt. I think you might be on to something. I'll inspect the wires on the O2's and see what I can find. When referencing banks 1&2. Which side is 1 and which side is 2 ? I think I've always...
  6. Replies
    13
    Views
    1,112

    Yea, I think that's because I'm playing with the...

    Yea, I think that's because I'm playing with the pedal. That log was me pulling out of the driveway in reverse. Placing it in drive and then flooring it going nowhere. I then went back into the...
  7. Replies
    13
    Views
    1,112

    Good morning, Yea, the pressure stays after...

    Good morning,

    Yea, the pressure stays after engine is cut off. Might be worth checking again but the few times I did it was okay. Seems as though the Regulator and Injectors are holding pressure...
  8. Replies
    13
    Views
    1,112

    Quarterhorse shows the maf voltage moving as it...

    Quarterhorse shows the maf voltage moving as it always has so I don't think that's an issue. Have a fuel gauge on the test port, reads 30-40 at idle. Problem is car only has issues when driving...
  9. Replies
    13
    Views
    1,112

    Hesitation\hard idle (sometimes)

    Solved the problem, sold the car.
  10. Replies
    1
    Views
    368

    I think I still have a set. Let me dig them up...

    I think I still have a set. Let me dig them up and I'll send some pictures.
  11. Replies
    0
    Views
    461

    SCP Air Box, 3"OD Tube, 4"OD Filter

    I have a SCP Air Box that came with their Fresh Air Intake Kit. I also have a 3" OD tube but this is home made and not from the SCP kit. Also have a 4" OD cone filter. Filter is squished a bit but...
  12. Replies
    1
    Views
    547

    DPFE Sensor Diagnostics HOWTO

    I recently fixed trouble codes 332 and 335 on my SC the other day. These two codes on the '94 - '95 SC's point to a possibly failed Pressure Feedback Sensor or some type of issue with the EGR system....
  13. Replies
    2
    Views
    622

    I'm looking for the front passenger side, yea....

    I'm looking for the front passenger side, yea. Inside of car? Could you send me some pictures by chance?

    Thank you,

    Bryce
  14. Replies
    2
    Views
    622

    FR ABS Sensor 94/95SC

    Looking for a Front Right ABS sensor for a 94/95 SC.

    Thanks,

    B
  15. Replies
    0
    Views
    544

    Pillar Pod 2 Gauge 94-97 Thunderbird

    I have a 2 Gauge Pillar Pod for the 1994-1997 Thunderbirds. I'm including the spray can I painted it with, too. Below are the details, let me know if you have any questions.

    **************

    Auto...
  16. Sold, thank you.

    Sold, thank you.
  17. Falcon, You forgot to include the shipping.

    Falcon,

    You forgot to include the shipping.
  18. Replies
    2
    Views
    699

    Sold, thank you.

    Sold, thank you.
  19. Replies
    2
    Views
    699

    3.8L Billet Aluminum Wire Looms

    I have a set of used 3.8L Billet Aluminum Looms. These were created for use with a set of LiveWires. I'm asking $30.00 shipped to your door.


    Regards,

    Bryce
    ...
  20. 5% Overdrive Jack Shaft Pulley - Lightweight Aluminum

    I have a never used 5% Overdrive Jack Shaft Pulley made from Lightweight Aluminum. It was purchased from Super Coupe Performance. I had plans to use on my built car but it never happened. It's 100%...
  21. Replies
    0
    Views
    516

    4r70w AT fluid lines

    Looking for an original set of 4r70w fluid lines to connect up to the radiator.

    95 sc

    Thanks,

    Bryce
  22. Replies
    3
    Views
    542

    Duplicate.........

    Duplicate.........
  23. Replies
    3
    Views
    542

    That would be ideal but 89-93 pistons\rods would...

    That would be ideal but 89-93 pistons\rods would work, too.

    Measurement from old pistons were 96.13 mm \\ 3.785"
  24. Replies
    3
    Views
    542

    pistons and 4r70w fluid lines

    Looking for a good set of "Standard" sized pistons for a rebuild. Please verify ring landings are in good condition and leave the connecting rod attached.
    I took my engine apart and found that five...
  25. Thread: drive line loop

    by 90coug
    Replies
    1
    Views
    456

    drive line loop

    I'm in need of a drive line loop for the drag strip. Please let me know if you have one.

    Thanks,

    Bryce
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4