Search results

Sorry to be so long in replying. I haven't been able to get to the garage in a month so have not continued my search. Compression is excellent, I was on my second fillip when it died so Gas isn't an issue. I will try to get motivated again this January once the snow is gone and really try...

fFnally was able to get to my rented garage. Man I wish I had a garage at home! ohm’d the injectors they range from 10.74 to 10.95. everyone one of them switches. I guess I will start again with the “no start” checklist. super frustrated. URGH!

I got a new harness from John Ludorf and replaced it. Following the no start guide got me to that point. There is no upshift light on cranking though I replaced my crank sensor with my spare just to be sure. I have spark and my noid light flashes on each injector. Given I have spark and a...

Thanks for all the replies! I did re-wire that melted plug even though I did not know what it was for. I have pulled the injectors and am going to take them in to get tested. There was a short in the cam sensor / crank sensor wiring so perhaps that fubar'd my injectors. I will post the...

Still can't get it to start. I have spark and I have a flashing noid light at the injectors. I I have 40lbs fuel pressure when the key is turned on. To ensure that the ecu powers the pump I relieved the pressure and then cranked and the pressure came back up. Is it possible that all the...

There is an air dam under the front that should direct air up to your radiator. These often fall off, or get taken off. double check that it is still there.

I will send you a PM.

Dave: John also has an M2Y.

Dave: sorry about that. I have a Z1Z2, I can grab an X1X2 from Mike Pucket and John Ludorf has a bunch of LOE1’s plus he has a ‘92 that he hasn’t pulled the EEC from yet. my car is in a garage about 30 minutes from my place here in downtown Vancouver so I have to wait till Saturday to go and...

Dave: Thanks for the reply. The tune you supplied me, way back when, is a GSALI. I do have spark. I attached Noid light to the injectors, and nothing. I assume that is what you meant by AC signal. If not I don't know how to test for that. I replaced the IRCM with a tested, matched one from...

Still trying to get my ‘91’s injectors to fire. I have traced back all the wiring, the PIP works, the only thing left now is the EEC. Mike has a EEC from a ‘91 but it is from an auto and I have a 5-speed. I searched the web but could not find any listing of compatible EEC’s. I am running a QH...

Mike: Thanks for the reply. I have a Z1Z2. I will try to find out the compatibility and get back to you. Sean

Do you have an EECIV? I need one for a ‘91. Regards Sean

I sent you a message re ’91 EEC.

I am looking for a '91 EEC. I will need it shipped via US Postal, not ups or fedex. Please let me know. Regards Sean

Still no luck. The circuit board looks fine. I removed the QH and tried to start without it, but nothing. I checked the impedance on all the injectors, all of them between 11.5 and 12 ohms. The only thing left that I can see is the EEC itself. Will check with Ludorf and hope he has one to...

Thanks for the reply. I did a KOEO test and got 111. There were no other fault codes but as the battery got discharged any stored codes are gone. I will have a look at the circuit board and see what it looks like. Sean

Went through the evtm and wiring diagram to track down all the connectors. The PIP is working and there is no resistance on pins 56 and 16 to pins 1 and 3 respectively. I cut out my melted connector from beside the transmission to clean that up but I can't imagine it has anything to do with...

I had the QH swapped over to the replaceable battery one. I will pop it off the EEC and see what happens. I hadn't thought it would have thought it would have lost it's charge already but I have spares so will replace it nonetheless. The car was running when it died so I am pretty sure it...

Thank for your reply. Inertia switch is closed. Fuel pump comes on and delivers 40lbs to the rail. I had installed a remote cutoff switch at the inertia switch as my car had been stolen but that has been removed for now and the wiring is returned to stock. Sean