Search results

  1. Mike Puckett

    WANTED 1994 SC cluster surround trim & TAN driver door panel

    I've got a tan door panel. I'll check it tonight and make sure it's in good condition.
  2. Mike Puckett

    Rough, miss-like idle

    I have had fouled O2 sensors cause a bad misfire. It would barely run enough to drive around the block. After replacing them it ran normally.
  3. Mike Puckett

    Rough, miss-like idle

    Sounds like DIS or coil pack problem or any connection between them. Once had an idle stall problem which turned out to be the sc belt rubbing on the wire bundle to the cam and crank sensors, so you never know what you might find.
  4. Mike Puckett

    Rough, miss-like idle

    You might want to check your O2 sensors, also. A bad O2 sensor can make it run really rough.
  5. Mike Puckett

    Southeast SCs - Any meetup in the works?

    PM me your phone number and I'll call you next time we do something.
  6. Mike Puckett

    Southeast SCs - Any meetup in the works?

    Every once in awhile we get together for lunch on Friday over here in the Norcross Tucker area. There's 3 of us who still daily drive our SC's. We can do a Sunday afternoon lunch meet if enough show up. We usually have trouble getting people to show up so don't do too many get togethers on...
  7. Mike Puckett

    Crank Position Sensor

    I ordered one online from NAPA but I heard nothing back so I called them to follow up and was told that they are not available at all even though they still show up on their website.
  8. Mike Puckett

    93 HVAC fan control module

    Oh OK. Thanks.
  9. Mike Puckett

    93 HVAC fan control module

    That looks like it. How much?
  10. Mike Puckett

    93 HVAC fan control module

    I can't tell for sure and I don't have access to it right now. How thick is the heat sink under the transistor? Edge view?
  11. Mike Puckett

    93 HVAC fan control module

    I don't have possession of it right now but it is about 2.5" square and about an inch thick with a large round power transistor mounted on a heat sink on one side of the module.
  12. Mike Puckett

    93 HVAC fan control module

    I'm needing the fan control module for a '93. This is the small module with a power transistor and heat sink that is mounted under the dash in front of the blower fan for the hvac and just behind the glove box.
  13. Mike Puckett

    Looking for an ABS pump motor

    I've got a bad one. It's tight but you can turn the shaft with pliers. You can have it for shipping, the pump, too if you want.
  14. Mike Puckett

    Needing EEC for 91 AOD

    Thanks for the thought but they have to be the exact type. A COS was tried but it didn't work.
  15. Mike Puckett

    Needing EEC for 91 AOD

    The code is X1A2. There is also F1WF-BC on it as well.
  16. Mike Puckett

    M5r2 major shift problems

    I rebuilt an M5R2 for someone a few years ago that had been rebuilt before. They had put 90 weight gear lube in it and every blocker was half stripped of lining. Usually 1st and 4th don't look too bad but it is possible that they could all be bad. You'll need to pull it and open it up to find...
  17. Mike Puckett

    Speedo off?

    I do believe that we have the 8 tooth speedo gear. My 89 had a jumpy speedo so I changed out the entire sending unit and the problem cleared up so you probably do have a bad sending unit. I also have discovered that the 23 tooth gears don't hold up. The teeth are just too thin. Had one last only...
  18. Mike Puckett

    M5r2 major shift problems

    If you're sitting still with the clutch pedal pushed in, does the car creep forward? If not, how far up does the pedal go before it starts to pull forward?
  19. Mike Puckett

    *found* Rear toe bolt

    If its the one with the dial on it, I've got some.
  20. Mike Puckett

    Power steering pump pulley

    I've got a couple of them if you're still looking for one.
Top